|
# of Beeps (in Guide)
|
Error Type
|
Solution
|
|---|---|---|
|
1 (Continuous tone-no breaks)
|
Ground Lost (Reconnect ground)
|
Check line and neutral connections as they may be reversed in the adapter or outlet. Unplug and reboot Waybox. If issue persists, please contact Support.
|
|
1 (Long beep-short break)
|
Waybox System Fail (Contact support)
|
Unplug and reboot Waybox. If issue persists, please contact Support.
|
|
2 (short beeps, then break)
|
Car not obeying J1772. (Or plugged into something that’s not an EV)
|
Unplug and reboot Waybox. If issue persists, contact Support.
|
|
3 (short beeps, then break)
|
GFI Trip (Check your connection)
|
Unplug from car in order to reset the GFI trip count to 0. If issue persists, contact Support.
|
|
4 (short beeps, then break)
|
OverHeat
|
Move your Waybox to a cooler area, out of direct sunlight, or remove heating sources from area. The Waybox will automatically resume when it cools off.
|
|
5 (short beeps, then break)
|
Relay Stuck Closed (Disconnect immediately. Contact support)
|
Check your ground wire in both the panel, and at the device termination (hard-wired or outlet plugged into) to make sure all connections are tight. If error persists after unplugging and rebooting the Waybox, and your car will not charge, please contact support.
|
Previous Generation (built Aug 2015 to Feb 2017)
Constant Buzzer Tone: (no interruption)
"No ground" error. Check that your circuit ground connection is established. On 240v single split-phase AC power (US standard), you should find approximately 120V between each line and the ground terminal of your outlet. The Ground connection is usually connected to Neutral at the circuit panel. When using a 240V Line-to-Neutral, single-phase mains supply, the Line and Neutral connections should not be reversed. If you find them reversed, please switch them to the correct L1 (H) and L2 (H/N-Comm). If this error persists unplug and reboot the Waybox. If it occurs intermittently or continues to occur, contact support.
1-Second Repeating Beep Tone:
This error code Indicates possible failure of Ground Fault Interrupter (GFI) circuitry. If this error persists unplug and reboot the Waybox. If it occurs intermittently or continues to occur, contact support.
2-Beep Tones:
This error code Indicates unintended closure of relay in non-charging state. Unplug unit from wall outlet to prevent unsafe charger state. If Waybox continues to signal this error, contact support.
3-Beep Tones:
This error code happens after a Ground Fault Interrupter (GFI) trip event. The unit will remain inoperable for 15 minutes, during which time the unit will continue to produce the 3 buzz error tone every 15 seconds, and will self-reset after 15 minutes. After 4 GFI trip events and automatic resets, the unit will not self-reset, and will continue to produce the 3 buzz tones every 3 seconds until the car is unplugged. The GFI trip is likely either caused by a wiring problem in the car or J1772 charging handle, or by significant line noise. If you continue to have this issue please contact support for further instructions.
4-Beep Tones:
This error code indicated that your Waybox is overheating. The Waybox is too hot (over 80C internally). Move your Waybox to a cooler area, out of direct sunlight, or remove heating sources from area. The Waybox will automatically resume when it cools off.
5- Beep Tones:
This error code indicated that the relay is stuck open. The relay should have closed for charging. The ground conductor on the circuit may also cause this error. Check your ground wire in both the panel, and at the device termination (hard-wired or outlet plugged into) to make sure all connections are tight and that the ground line is properly connected - see above for "no ground" issues. If error persists after unplugging and rebooting the Waybox, and your car will not charge, please contact support.
6-Beep Tones:
This error is an internal system fault - usually related to pilot signal generation. Check that your control pilot (CP) signal pin isn't shorted. Contact Support if this code persists.
(rare) Early Buzzer codes (July-September 2015):
*Information applies to Wayboxes built prior to August 28th 2015
In the event of a system error, the Waybox unit will produce an audible sequence of tones to indicate its error state. Buzzer tone sequences for error states are listed below. The sequence is a "Tii-duu" (High-Low) dual tone (intended to mean "Uh-oh!"), followed by a number of "Tii" (high) beeps to indicate which error is signalled. The tone pattern typically repeats so you can identify it.
1-Beep Tone: Ground Monitor Interrupt
- Occurrence of this error state indicates that the unit is not connected to an earth grounded outlet. Please unplug unit and ensure outlet intended for use is earth grounded before attempting to use Waybox.
2-Beep Tones: Ground Fault Interrupt Startup Self-Test Failure
- Occurrence of this error state indicates a failure of the ground fault interrupt system self-test during unit power on. Unplug unit from wall outlet to prevent unsafe charger state.
3-Beep Tones: Stuck Relay Event
- Occurrence of this error state indicates unintended closure of the Waybox's relay when the unit is not charging a vehicle. Unplug unit from wall outlet to prevent unsafe charger state.
4-Beep Tones: Ground Fault Interrupt:
4th Fault Error (no beep for first 3 trips with 15-minute auto-reset)
- After a Ground Fault event the Waybox will enter an inoperable state for 15 minutes for safety. After 15 minutes, the unit will enter an operational state. If the ground fault is still present, the unit will repeat the 15 minute waiting period. The Waybox will repeat this 15 minute waiting process 4 times in total, after which the unit will become inoperable until it is hard reset via power cycling.